|
※
※ |
|
Model:PSIV-620-2 |
Issue Date : 20030809 |
Rev :1.0 |
| 1.
Introduction: |
|
This
Is An EPS-12V Power Supply Of Specification. |
| 2.
AC Input : |
|
|
2.1 Input Voltage Range: |
103
To 132V AC Or 206 To 264V AC Rms Switch-Selectable |
|
2.2 Input Frequency: |
50
TO 60 Hz. |
|
2.3 Input Current: |
10A
Rms Max. for 115 V AC |
| 5A
RMS Max. for 230 V AC |
|
2.4
Max. Inrush Current: |
40A
for 115 V AC Cold Start |
| 80A
for 230 V AC Cold Start |
| 3.
Output: |
|
3.1
Voltage: |
+3.3VDC |
+5V
DC |
+12V
DC |
-5V
DC |
-12V
DC |
+5VSB
DC |
|
3.2 Tolerance: |
+/-4% |
+5/-4% |
+/-5% |
+/-8% |
+/-10% |
+2/-4% |
|
3.3 Max. Current: |
28A |
30A |
34A |
0.3A |
0.8A |
2A |
|
3.4 Min. Current: |
0.3A |
0.1A |
0A |
0A |
0A |
0A |
|
3.5Peak.Current: |
|
|
37A |
|
|
2.5A |
|
3.6 Ripple&Noise: |
50mV |
50mV |
120mV |
100mV |
120mV |
50mV |
|
3.7 Line Regulation: |
+/-1% |
+/-1% |
+/-1% |
+/-2% |
+/-2% |
+/-1% |
|
3.8 Load Regulation: |
+/-3% |
+/-3% |
+/-4% |
+/-5% |
+/-5% |
+2/-4% |
|
3.9 +5V & +3.3V Combined Load |
:220W
MAX |
|
3.10 +12V +5V
& +3.3V Combined |
:500W
MAX |
|
3.11Total Output Power |
:520W
MAX |
| 4.
Electrical Specifications: |
|
4.1 Efficiency: |
70%Min.
Under Max. Range Load |
|
4.2 Rise
Time |
20Ms
Max |
|
4.3 Hold Up Time: |
Min.
10mS at Full Load And Nominal Input Voltage
|
|
4.4
STABILITY |
+/-0.5%
after 24 hours warm up |
|
4.5 Power Good Signal: |
+5V
TTL compatible signal out with 100mS to 500mS delay after power set
up |
|
4.6 Power Fall Signal: |
TTL compatible signal ,ps-on
# Is Low, The Power Turn Off Power , Ps-On# Is Low
, The Power Turn On.
|
|
4.7Overshoot: |
10%Min.
Above The Nominal Voltage. |
|
4.8Power Fall Signal: |
+5V
TTL compatible Turn-Off
At Least 1Ms Before +5v Fall Below 95% Of Normal. |
|
4.9 Leakage Current: |
3.5Ma
Min. At 240VAC. |
|
4.10 Fan Noise Killer |
Fan
Speed Contra Function Inside (Option) |
| 5.
Output Protection: |
|
5.1 Short Circuit Protection: |
All
Output Equipped With Short Circuit Protection. |
|
5.2 Over Current Protection: |
150%
Max. |
|
5.3 Over Voltage Protection: |
:+3.3V
OUTPUT:3.7~4.1 |
|
:+5V
OUTPUT:5.7~6.5 |
|
:+12V
OUTPUT:12.8~13.9 |
| 6.
Environmental: |
|
|
6.1 Operating Temperature: |
0
to +40 degree C |
|
6.2 Storage Temperature: |
-20
to +85 degree C |
|
6.3 Storage Humidity: |
10%
to 90% RH |
|
6.4 COOLING: |
Forced
Air Ventilation by 8cm DC Fan |
|
6.5 Operating Altitude: |
To
10,000 ft |
|
6.6
Operating Humidity: |
20%
to 90% RH |
|
6.7 Storage Altitude |
To
50,000 ft |
|
6.8 Vibration |
10-500Hz,.2G
10Min / Tcyle , Period For 60Min. Each Axes. |
| 7.Reliability: |
|
|
7.1Mtbf |
100k
Hours At Max, Load
, Normal Line And Degree 25 |
| 8.Mechanical: |
|
|
8.1Physical
Dimensions |
168.6(L)x150(W)x86(H)mm. |
|
8.2Fan |
80mmDC+12V.Sleeve. |
|
8.3AC
Connectors |
IEC
320 Type |
|
8.4DC
Connectors |
Figure
1 Shows Pinpoints And Profiles |
| 9.
Safety Standard: |
Approve
CB IEC 950 / TUV EN 60950, / UL1950 / CSA 950 |
| 10.EMI
Standard: |
Approve
EN 55022(CISPR22), EN 61000-3(PFC),EN 6100-4 |
|
Approve
FCC Part15 |
|
Approve
Bsmi CNS 13418 |
| 11.
Dielectric Withstand (HI-POT) Test |
|
11.1 Input To Output |
1500VAC
FOR 1 SEC. |
|
11.2 Input To Frame Ground |
1500VAC
FOR 1 SEC. |
| 12.
Insulation Resistance: |
|
12.1 Input To Output |
500VDC
/ 50M Ohms |
|
12.2 Input ToFrameGround |
500VDC
/ 50M Ohms |
